*MAFIA* Forums
*MAFIA* => Flame => Topic started by: *MAFIA* KrautKiller on December 09, 2006, 01:25:11 PM
-
Finally got all the parts in my computer and now the computer will not start... The power supply doesnt even have any voltage coming from the male pronges... Fan doesnt even work 5 volts going to motherboard pissing me off... Atleast ill have more time when this senior project is out of the way...
Im done flaming :D
-
did u set it up?
-
everything is plugged into the right things, im taking it back to compusa in 10 minutes, once this is done im done with my senior project yay!!!
-
Take it to chris!
-
everything is plugged into the right things, im taking it back to compusa in 10 minutes, once this is done im done with my senior project yay!!!
I'd expect to pay no less that $150 from comp-usa. I'm guessing that you've missed a jumper or have the configuration of the power switch setup wrong.
-
na the fan would be on in the power suppply and it doesnt come on.
-
I bought a power supply from newegg for 20 bucks and it ran for 3 years and is still running strong ;) compusa=CRAP!
-
na the fan would be on in the power suppply and it doesnt come on.
Even if you have power to the supply you would still have to switch it on for the fan to start working. Look over your case and motherboard documentation again before taking it over to compusa and blowing your money.
-
God damit balth your fucking right i wasted 30 minutes driving there to find out your right.. Gonna be a awesome computer if i can finish it..
-
God damit balth your fucking right i wasted 30 minutes driving there to find out your right.. Gonna be a awesome computer if i can finish it..
I figured as much, it's all about the documentation. Good luck in hooking it up.
-
Always read directions on things, even if you think you know what you're doing. It usually saves time.
-
Like reading the bible just to know you are going to hell, right beetle?
-
The directins that came with the tower and the video cards and the supply were all useless, the motherboard booklet is the only thing im going off of. The motherboard makers should be making the towers and stuff too... :(
-
The directins that came with the tower and the video cards and the supply were all useless, the motherboard booklet is the only thing im going off of. The motherboard makers should be making the towers and stuff too... :(
Useless because they are difficult to understand? Send me the specs of your tower and mother board and i'll see if I can get you figured out.
-
Well my mentor is coming on sunday hes like a geeksquad guy so he should be able to set it up. hopefully
-
NERDS!!!
-
Ok ive ran into another problem, here it is..
The monitor is saying "no digital signal"
Anyone know what this means?
-
Ok ive ran into another problem, here it is..
The monitor is saying "no digital signal"
Anyone know what this means?
Ok, first of all, make sure the computer is ON. Then depending on what type of connection method u r using, set it on that. For example, if using DVI, set your monitor on that number to accept the signal. Usually a button on ur monitor that will let you change inputs.
Hope this helps.
-
Ok, first of all, make sure the computer is ON. Then depending on what type of connection method u r using, set it on that. For example, if using DVI, set your monitor on that number to accept the signal. Usually a button on ur monitor that will let you change inputs.
Hope this helps.
Good stuff Roshan, you will soon become as much of a nerd as me.
Kraut, I assume that you have a higher-end video card. If this is the case make sure you have power getting to the bad boy. This is to say that you will most likely have a slot on your card to hook up your power supply to your card (i.e. Molex connector). Without power the card will not be able to display anything.
If this still doesn't work try reseting your BIOS. You will have to look over your motherboards documentation to see which jumper to remove to be able to reset it. Or you can do it the quick and dirty way by removing your CMOS battery, turning on the system and leaving it on for a minute or so, shut the system down, put the battery back in and start the system up again.
There is also the issue of your BIOS settings if you get it reset...
Does your motherboard have onboard video? If so you will need to disable it before you will be able to use a PCI-X or AGP card.
Troubleshootin g is fun!
-
Dude, hit alt f4 and it should work
-
kraut, make sure your Ram works with your motherboard... it took me 2 months and 3 video cards to figure that one out...
-
kraut, make sure your Ram works with your motherboard... it took me 2 months and 3 video cards to figure that one out...
rofl, god damn blak u are funny......... lol. but yeah the geeksquad can suck a nut, they don't know crap...
-
Im getting compusa to figure it out, ive already done more work this year on this project then ive done my whole high school years lol
-
kraut, make sure your Ram works with your motherboard... it took me 2 months and 3 video cards to figure that one out...
One of the guys at compusa who i play bf2142 with sometimes picked all the stuff out for me.
LAtest update :D
I blew my motherboard yay.
-
One of the guys at compusa who i play bf2142 with sometimes picked all the stuff out for me.
LAtest update :D
I blew my motherboard yay.
lol, kraut didnt you learn about static electricity in highschool?
-
One of the guys at compusa who i play bf2142 with sometimes picked all the stuff out for me.
LAtest update :D
I blew my motherboard yay.
ROFLCOPTERS... That's why they make Dells Kraut. I know you can afford it so just go buy an XPS system.
-
Get you a dell you rich nazi bastard you!
-
Well its finaly running its in my schools media center til the 15th :D